I recently read a list of 10 “home energy myths” published by Consumers Energy. Many of these myths directly relate to how we conserve energy in schools.

Check them out:

1. Setting the thermostat higher or lower will heat or cool your home faster. Homeowners often set the thermostat higher or lower than necessary, thinking it will warm or cool their home faster, but furnaces and air-conditioners work at the same speed, no matter what the thermostat setting. A home will warm up to 70ºF just as quickly if the thermostat is set at 70ºF as it will if it is set at 80ºF. In fact, more energy may be wasted as the heating or cooling system continues to run to reach the higher set point.
2. A heating and cooling system works harder to reach a comfortable temperature after setback or set forward. Many homeowners do not adjust their thermostat at night or when their home is unoccupied because of the common misconception that the heating or cooling system must work harder or use more energy to reheat or re-cool the house, but this is not how thermostats work. The system turns on to reach a set level and shuts off when that level is reached. It operates more like a switch that shuts on and off than a car that accelerates when you step on the gas pedal.
3. Energy efficiency and energy conservation are the same thing. Efficiency refers to using less energy to perform a specific task. For example, compact fluorescent lamps (CFLs) can light your home using less energy than conventional incandescent bulbs. Conservation involves reducing your need for energy through behavior changes, such as setting your thermostat lower. 
4. When an appliance is turned off, it is off. Many appliances and home electronic devices continue to use power after they have been turned off—sometimes as much as if they were on. This is known as standby power or phantom load. The only way to stop the drain of power from these devices is to unplug them.
5. CFLs are more harmful for the environment than traditional bulbs because they contain mercury. CFLs do contain a trace amount of mercury that can be emitted into the atmosphere if the bulb is broken. However, mercury is also emitted into the atmosphere through electricity generation. Using CFLs will help to reduce mercury emissions because they are more efficient and use less electricity. According to the U.S. Environmental Protection Agency, a typical 60-watt incandescent bulb will result in 5.8 milligrams of mercury emissions over its lifetime, while a comparable CFL bulb will emit only 1.8 milligrams—even if it ends up in a landfill. Recycling CFLs can further reduce emissions. To recycle CFL bulbs go to Earth911. Make sure to type in Compact Fluorescent Lightbulbs and then your city to view the list. Typing in CFL won’t work.
6. Leaving lights and electronic devices on uses less energy than turning them on and off. In most cases, the small surge of power needed to start a device is much less than the power that is wasted by leaving it on when it is not needed.
7. Duct tape is the best choice for sealing ducts. Duct tape has very low durability when used to seal ducts. Over time, it will fall off as the adhesive dries out and the tape starts to wrinkle. Mastic or metal-backed tapes—available at your local hardware or do-it-yourself retailer—are better choices for duct sealing.
8. Purchasing an efficient air-conditioner or furnace will automatically reduce energy bills. This is true to some extent, but the system must be sized correctly to achieve optimal energy savings. Installing an efficient, but over-sized, system may negate much of the potential savings, while a poorly designed duct system will also affect efficiency and comfort. Windows, doors, and insulation also affect heating and cooling efficiency.
9. Dimming lights by 50% will cut lighting costs in half. Dimmed lights do use less power, but the relationship between light loss and energy savings is not quite direct. Dimmer switches actually use a small amount of power, thereby reducing the overall savings. Dimming lights by 50% may only result in energy savings of 40%, and the amount of savings may vary depending on the type of light in use. 
10. Closing off vents will help to lower heating and cooling costs. Closing or covering up vents is typically not a good way to save on energy costs. Heating and cooling systems balance their load throughout the duct system. If one vent gets closed off, it throws the system off balance. Pressure can build up in the ductwork, causing leakage and reducing the amount of air circulating in your home.